Hoops for (NEW) Babylock Ellure Made in 2006 Machine

5 Hoops 2 Double-Wide and 3 additional hoops listed below to choose from or buy them all for incredible versatility!

How can your sewing machine use these hoops?

With a specially designed spacing base, we s-t-r-e-t-c-h your sewing machine apart! In addition to a factory approved extension cord that tricks your machine into thinking it is connected the normal way.

See how much bigger our hoop is than your machine's largest hoop!

The support tables are designed in 4 pieces so you do not have to have a workspace as large as you would if it was a single piece. When the largest hoop (Super Double-Wide) is set up, the measurement or space required on your table is, 30" wide by as little as 20" deep. Illustrations below show how to use these hoops on a smaller surface or workspace by alternating the use of front or back table tops and sliding the machine forward and back.

You must know how to use the software for your machine in order to use the hoops to their fullest potential. In order to fill in a complete hoop with a SOLID design, you must SPLIT designs so that the machine will accept the design. Until you have a complete understanding of your software you CAN use these hoops for simplified hooping and extra length.

You must use our support table with the specially designed base in order to stretch the machine to the exact limit and to support the ennormous size of these hoops. Failure to use the recommended support table and base with these hoops can damage your machine's embrdoidery unit.

Your work area must be large enough to hold the spacing base and to allow for the hoop to slide all the way forward and all the way back. To prepare your workspace be sure to have an area cleared that measures: 36" wide by 28 " long.

The Double-Wide Extension base is required in order to position the embroidery unit and machine the exact distance away from one another allowing for the wider hoops. This specially designed base also ensures that the embroidery unit is properly aligned with the machine.

Why do you need to purchase the new Double-Wide table if I already have the Giant-L. Hoop-It-All first released the exciting Giant-Long hoop (shown at bottom of page) for these machines. If you have already acquired the Giant-Long hoop the Standard table pictured above on the left was included with your kit and can be used with our new Super Giant -Long Hoop also shown at the bottom of this page. These tables are significantly smaller than the new Double-Wide tables.

If you already have the Giant-Long or Super Giant Long and want to know if you can use the base --- No. You absolutely cannot. The base is what makes it possible to stretch your machine apart. Without the base and cable your machine and embroidery unit will not be in-line. Not following our recommendation places your machine at risk of serious damage. Therefore the cables are not sold separately under any circumstances.

If you are considering using your Giant-Long and/or Super Giant-Long table front and back with the Double-Wide Base you will soon see why it is not a good idea. Open gaps will be revealed that can cause your bobbin thread to become caught on the edges of your embroidery unit causing the hoop to stop moving while the embroidery unit continues to move and causing the embroidery unit to go out of calibration, or even worse. Additionally, if you think about the fact that the hoop is twice the width of the other hoop; it is clear that the hoop will not receive enough support to protect your machine from any possible damage and therefore not feasible. (We did make every attempt to design the Double-Wide Hoops using the table you already have and were frustrated just as you are now that it didn't work. However, we are sure that you can see the benefits out-weigh the costs.) Therefore, we strongly recommend that Double-wide TABLE FRONT -and- BACK be used with all Double-Wide hoops.

It is not necessary to split designs or to use software programs with the Double-Wide Hoops. You can create larger designs than your machine can sew in a single sewing field by simply combining normal designs together to create a collage making your own one-of-a-kind picture. The photos within our photo gallery are an excellent source of examples of how creative you can be using designs that you already have or those you might choose to download from the Internet.

There are however, some reasons to use software with our hoops, for instance, if you want to embroider a single design that is larger than a single design would normally be for your machine, or if you want to gather together different pieces/elements of designs cards on your screen creating a unique design. Your fabric becomes a canvas that you fill in using whatever individual design you like on many different cards. Most of the design samples that you see here on our site were created by using built-in designs, memory cards, stock designs and smaller designs downloaded from the Internet and then combining them together.

Using our Giant hoops does not suddenly make your machine capable of sewing a larger sewing field than it was designed to sew out. Our hoops simply make it so that you are not required to re-hoop your fabric. With special embroidery software you can embroider designs larger than your machine’s embroidery field. You can place these oversized designs anywhere you desire within the hoop frame. (Scroll down page to see 4-part illustration showing this process.)

There are several software products available that split these oversized designs into the proper size for your machine. This allows you to then embroider these designs in sections, like piecing a puzzled together. Once the embroidery is completed and all pieces are sewn, it appears as if you embroidered a huge design with your machine all at once. Ask your dealer which splitting/slicing software programs are best for you and your machine.

The support tables are designed in 4 pieces so you do not have to have a workspace as large as you would if it was a single piece. When the largest hoop (Super Double-Wide) is set up, the measurement or space required on your table is, 30" wide by as little as 20" deep. Illustrations below show how to use these hoops on a smaller surface or workspace by alternating the use of front or back table tops and sliding the machine forward and back.

 

---

Double-Wide Hoop Spacing Base with Extension Cord and Deluxe Front & Back Table Supports

Back table is removed, machine slid back and front table supports hoop in front as you embroider the first section of the hoop.

Back table is removed, machine slid back, hoop is removed from within the sliding bracket. Both the hoop and the designs are rotated 180 degrees. Hoop is re-inserted into sliding bracket and the front table supports hoop as you embroider the third section of the hoop.

If your table is large enough to leave both the front and back sections of the table in-place simply disregard the table refrences on the above instructions.

The following hoops, use the same Attachment Bracket...So you only need 1 complete kit and then you can buy the other hoop frame separately to increase your hoop selection. The Super Giant-L hoop requires its own table and base.

Done Using the Quilter's Square frame above on the 8200 in a single hooping without having to rotate the design!

DOUBLE WIDE HOOP KITS

Frames Sold separately can only be used if you already have the Spacing base, Support table & attachment Bracket. If you do not, refer to the kits above and then you can accessorize by purchasing additional hoops below. All 3 hoop frames fit into the same bracket and use the same support table.

Accessories sold Separately

You can also order the following hoops with cap sewing feature to add flexibility to your embroidery supplies.

This hoop replaces the large hoop for your machine and makes it so you can sew a larger design than you currently can with the machine's large hoop. You can also use this hoop to embroider small designs.

Medium hoop with clamp designed to hold baseball caps in place.
This hoop can be used in place of your machine's Medium hoop and with its specially designed clamp it holds baseball caps in place too! You never have to "Hoop" the fabric because you adhere our SIA to the back of the hoop and then simply lay your fabric on the sticky surface.

BIG hoop with clamp designed to hold baseball caps in place.
This hoop can be used in place of your machine's Large hoop and with its specially designed clamp it holds baseball caps in place too! You never have to "Hoop" the fabric because you adhere our SIA to the back of the hoop and then simply lay your fabric on the sticky surface.

This is the first of the Giant Hoops produced for your machine and cannot be used with the same base and table that are used with the Double Wide hoop kits shown above. However you can use the base and table with the Super Giant-L Frame to add to your collection of hoops.
This hoop can be used in place of your machine's 3-position hoop and with its specially designed clamp it holds baseball caps in place too! You never have to "Hoop" the fabric because you adhere our SIA to the back of the hoop and then simply lay your fabric on the sticky surface.

Super Giant-L (Long) Hoop

This Hoop can be used with the Giant-L table abd base. However it cannot be used with the same base and table that are used with the Double Wide hoop kits shown above.